OBD Scantech Apps
Elm 327 Terminal 1.21
A simple program that will communicate with your ELM 327 OBD IIBluetooth adapter. The ELM 327 Bluetooth Adapter is a Device thatconnects directly to your Vehicles 16 Pin OBD II diagnosticconnector. Choose one of many commands from the list or you maytype in a valid command.HARDWARE REQUIREMENT: ELM 327 (Clone Type) BluetoothAdapter.Vendors Type: CHX, OBDII, BAFX Bluetooth Device tested OK.Disclaimer Notice:Do not attempt to enter information or adjust your device whiledriving. Failure to pay full attention to the operation of yourvehicle could result in death, serious injury, or property damage.You assume totalresponsibility and risk for using your device with this app.Requirement: Android 2.0 or higher for Bluetooth to functionproperly.
OBDDiag Toyota 1.05.31
OBD II App with Ads that will communicate withyour Toyota Engine ECU Vehicles. The Generic OBDII is also includedand will work with any OBD II Complaint Vehicle. The app requiresOBDII ELM 327 Bluetooth(See Below). It will read ToyotaEnhance/Extended PIDS(130 available) and Perform Output Test (70available). Not all of the PIDS are supported by the vehicle. Itwill support certain ranges of Toyota Models and Years (2000-2006Toyota). It may work on some of the Lexus Models.Currently, It will Support ISO-9141 PROTOCOL ONLY for theEnhance Toyota! CAN BUS is Not Supported for the EnhanceToyota!The Generic OBDII supports all of the Protocols.-----------------------------------------------------------The App Supports the Following (ISO-9141)-----------------------------------------------------------* Enhance Data Parameters* Output Test* Mode 3 - Read Faults* Mode 4 - Clear Faults* Mode 7 - Pending Faults* Generic Data Parameters (Any OBD II Complaint Vehicle)* Readiness* O2 Sensor Location* Mode 2 - Freeze Frame Data* Mode 3 - Read Current Faults* Mode 4 - Clear Faults* Mode 6 - On-board Test Result* Mode 7 - Read Pending Faults* Mode 9 - VIN, Performance Tracking Data, ECU Name, Calibrationand Verification ID* Mode A - Read Stored FaultsWill be supporting more features in the future release.Output Test parameters is not filtered thoroughly and some ofthe Output Test will not work, because the ECU does not supportit.Toyota Enhance Powertrain: Tested successfully on the followingvehicles* 2004 Toyota Camry* 2002 Toyota Camry SolaraDisclaimer Notice:Do not attempt to enter information or adjust your device whiledriving. Failure to pay full attention to the operation of yourvehicle could result in death, serious injury, or property damage.You assume totalresponsibility and risk for using your device with this app.HARDWARE REQUIREMENT:CHX, OBDII, BAFX and OBDLink Bluetooth Device tested ok.
Car Gauge Lite OBD2 3.61.14
You can create custom Dasboards and the application willcommunicate with the vehicles ECU at the 16 Pin OBD II diagnosticconnecter. Most of the OBD II connector location should be underthe Steering Wheel Compartment. ELM 327 Bluetooth Adapter isrequired to make this application work. Car Gauge Lite not only canbe exciting with Dashboards, it is a Professional Scan Tool. Do youhave a check engine light on? Do you want to know the ReadinessStatus will pass for a Smog Inspection? Do you want to check thefunctionality of the Sensors and determine the status of the Mode5/6 Emission On-board Test(Some Models may not support it)? CarGauge Lite will show you.***Car Gauge Pro available Car Gauge Pro(See information below for the hardware type requirement.)Vehicle computer system have multiple signal protocols and ELM327 supports many of them. Currently, the following protocols aresupported by the app and MUST be an OBD II Compliant Vehicle.[Protocols Supported]* VPW - 1996-2004 Year (GM vehicles)* PWM - 1996-2004 Year (Ford vehicles)* ISO 9141(Slow) - 1996-2004 (Chrysler, European, and Asianvehicles)* KWP 2000(Slow/Fast) - 1996-2004 (Chrysler, European, and Asianvehicles)* CAN (11/29 Bit) - (2004 and Newer)[Car Gauge Lite Supports the Following with Limited Views][OBD II Generic]* Mode 1 - Analog/Digital Gauges (160/215 Generic PIDS)* Mode 1 - List View (220 Generic PIDS)* Mode 2 - Freeze Frame Data* Mode 3 - Read Current Faults* Mode 4 - Clear Faults* Mode 5 - O2 Sensor Test Result (Non CAN Bus)* Mode 6 - On-board Test Result* Mode 7 - Read Pending Faults* Mode 8 - Evaporative System Leak Test* Mode 9 - Vin, Performance Tracking Data, ECU Name, Calibrationand Verification ID* Mode A - Read Stored Faults* I/M Readiness Status* O2 Sensor LocationDisclaimer Notice:Do not attempt to enter information or adjust your device whiledriving. Failure to pay full attention to the operation of yourvehicle could result in death, serious injury, or property damage.You assume total responsibility and risk for using your device withthis app.The App is setup for importing background, needle skins andgauge skins from SD card. You can download it from the website.HARDWARE REQUIREMENT: ELM 327 (Clone Type) Bluetooth Adapter orOBDLink MXVendors Type: CHX, OBDII, BAFX Bluetooth Device tested OK.
Diag My Toyota 1.00.12
OBD II App that will communicate with yourToyota Engine ECU vehicles. This app requires OBDII ELM 327Bluetooth(See Below). It will Read Enhance/Extended PIDS(130 PIDS).It will support certain ranges of Toyota Models and Years(2000-2006 Toyota). Currently, it will support ISO-9141 protocolOnly.Tested Successfully on the Following Vehicles*2004 Toyota Camry*2002 Toyota Camry SolaraDisclaimer Notice:Do not attempt to enter information or adjust your device whiledriving. Failure to pay full attention to the operation of yourvehicle could result in death, serious injury, or property damage.You assume totalresponsibility and risk for using your device with this app.HARDWARE REQUIREMENT: ELM 327 (Clone Type) Bluetooth Adapter.Vendors Type: CHX, OBDII, Vgate Bluetooth Device tested OK.
OBDDiag Toyota Pro 1.05.31
OBD2 App that will communicate with yourToyota Engine ECU Vehicles. The Generic OBD2 is also included andwill work with any OBD2 Complaint Vehicle. The app requires OBD2ELM 327 Bluetooth(See Below). It will read Toyota Enhance/ExtendedPIDS (130 PIDS available) and Perform Output Test (70 PIDSavailable). Not all of the PIDS are supported by the vehicle. Itwill support certain ranges of Toyota Models and Years (2000 -2006). It may work on some of the Lexus Models.ATTENTION: Try Free "DIAG MY TOYOTA" or OBDDiag Toyota with AdsBefore Purchasing this App.If it works, then you may take advantage with the Pro versionwhich includes Output Test, Nicer GUI, Better Support and morefeatures will be added.Currently, It will Support ISO-9141 PROTOCOL ONLY for theEnhance Toyota! CAN BUS is Not Supported for the EnhanceToyota!The Generic OBD2 supports all of the Protocols.-----------------------------------------------------------The App Supports the Following (ISO-9141)-----------------------------------------------------------* Enhance Data Parameters* Output Test* Mode 3 - Read Faults* Mode 4 - Clear Faults* Mode 7 - Pending Faults* Generic Data Parameters (Any OBD2 Complaint Vehicle)* Readiness* O2 Sensor Location* Mode 2 - Freeze Frame Data* Mode 3 - Read Current Faults* Mode 4 - Clear Faults* Mode 6 - On-board Test Result* Mode 7 - Read Pending Faults* Mode 9 - VIN, Performance Tracking Data, ECU Name, Calibrationand Verification ID* Mode A - Read Stored FaultsOutput Test parameters is not filtered thoroughly and some of theOutput Test will not work, because the ECU does not support it.Toyota Enhance Powertrain: Tested successfully on the followingvehicles* 2004 Toyota Camry* 2002 Toyota Camry SolaraHARDWARE REQUIREMENT: ELM 327 (Clone Type) Bluetooth Adapter orOBDLink MXVendors Type: CHX, OBDII, BAFX Bluetooth Device tested OK.
OBDDiag Generic 1.00.31
The application communicates with yourvehicles ECU at the 16 Pin OBD2 Diagnostic Connector. Most of theOBD2 connector location should be under the Steering WheelCompartment. ELM 327 Bluetooth adapter is required to make thisapplication work.See information below for the Hardware Type Requirement.Vehicle computer system have multiple signal protocols and ELM327 will support many of them. Currently, the following protocolsare supported by the app and MUST be OBD2 Compliant Vehicle.* VPW - 1996-2004 Year (GM vehicles)* PWM - 1996-2004 Year (Ford vehicles)* ISO 9141(Slow) - 1996-2004 (Chrysler, European, and Asianvehicles)* KWP 2000(Slow/Fast) - 1996-2004 (Chrysler, European, and Asianvehicles)* CAN BUS (11/29 Bit) - (2004 and Newer)-----------------------------------------------------------OBDDiag Generic Supports the Following-----------------------------------------------------------* Mode 1 - Data Parameters* Mode 2 - Freeze Frame Data* Mode 3 - Read Current Faults* Mode 4 - Clear Faults* Mode 6 - On-board Test Result* Mode 7 - Read Pending Faults* Mode 9 - Vin, ECU Name, Tracking Performance Data andCalibration/Verification Id* Mode A - Read Stored FaultsHARDWARE REQUIREMENT: ELM 327 (Clone Type) Bluetooth Adapter orOBDLink MXVendors Type: CHX, OBDII, BAFX Bluetooth Device tested OK.
